USB HID INTELLIHEAD FOR SWIPE READERS TECHNICAL REFERENCE MANUAL Manual Part Number 99875320-5 OCTOBER 2008 REGISTERED TO ISO
USB HID IntelliHead Swipe Reader HARDWARE CONFIGURATIONS The hardware configurations are as shown in the table below. Drawings of each model are
Section 1. Features and Specifications SPECIFICATIONS Table 1-1 lists the specifications for the USB IntelliHead. Table 1-1. Specifications Re
USB HID IntelliHead Swipe Reader 4
5SECTION 2. INSTALLATION This section describes the cable connection, the Windows Plug and Play Setup, and the physical mounting of the unit. USB
USB HID IntelliHead Swipe Reader 6
7SECTION 3. OPERATION CARD READ A card may be swiped past the read head at any time. The magnetic stripe must face toward the head and may be sw
USB HID IntelliHead Swipe Reader 8
SECTION 4. USB COMMUNICATIONS This device conforms to the USB specification revision 1.1. This device also conforms with the Human Interface Devic
USB HID IntelliHead Swipe Reader have a usage page in the range 0xFF00 – 0xFFFF. All usages for this device use vendor-defined magnetic stripe rea
Section 4. USB Communications Item Value (Hex) Input (Data, Variable, Absolute, Buffered Bytes) 82 02 01 Usage (Track 3 data) 09 32 Report Count
ii
USB HID IntelliHead Swipe Reader TRACK 2 DECODE STATUS Bits 7-1 0 Value Reserved Error This is a one-byte value, which indicates the status of
Section 4. USB Communications CARD ENCODE TYPE This one-byte value indicates the type of encoding that was found on the card. The following tabl
USB HID IntelliHead Swipe Reader COMMANDS Most host applications do not need to send commands to the device. Most host applications only need to
Section 4. USB Communications data. The HID specification requires that Reports be fixed in length. Command data may vary in length. Therefore,
USB HID IntelliHead Swipe Reader The result codes for the Get and Set Property commands can be any of the codes list in the generic result code tab
Section 4. USB Communications SERIAL_NUM PROPERTY Property ID: 0x01 Property Type: String Length: 0 – 15 bytes Get Property: Yes Set Property
USB HID IntelliHead Swipe Reader POLLING_INTERVAL PROPERTY Property ID: 0x02 Property Type: Byte Length: 1 byte Get Property: Yes Set Property:
Section 4. USB Communications MAX_PACKET_SIZE PROPERTY Property ID: 0x03 Property Type: Byte Length: 1 byte Get Property: Yes Set Property: Y
USB HID IntelliHead Swipe Reader TRACK_ID_ENABLE PROPERTY Property ID: 0x04 Property Type: Byte Length: 1 byte Get Property: Yes Set Property:
Section 4. USB Communications INTERFACE_TYPE PROPERTY Property ID: 0x10 Property Type: Byte Length: 1 byte Get Property: Yes Set Property: Ye
iiiC Printed in the United States of America lectronic or mechanical, for any purpose, ithout the express written permission of MagTek, Inc. agTek
USB HID IntelliHead Swipe Reader DECODE_ENABLE PROPERTY Property ID: 0x1A Property Type: Byte Length: 1 byte Get Property: Yes Set Property: Y
Section 4. USB Communications RESET_DEVICE COMMAND Command number: 0x02 Description: This command is used to reset the device. This command ca
USB HID IntelliHead Swipe Reader 24
SECTION 5. DEMO PROGRAM The demo program, which is written in Visual Basic, can be used to do the following: • Read cards from the device and vie
USB HID IntelliHead Swipe Reader 26 SOURCE CODE Source code is included with the demo program. It can be used as a guide for application develop
APPENDIX A. DRAWINGS The following drawings are provided in this section: Part Number Title 21030006 USB HID IntelliHead, 3-Track, 125mm wire, 5
USB HID IntelliHead Swipe Reader Figure A-1. USB HID IntelliHead, 3-Track, 125mm Wire, 5-Pin Connector 28
Appendix A. Drawings Figure A-2. USB HID IntelliHead, 3-Track, 440mm Wire, 5-Pin Reverse Connector 29
USB HID IntelliHead Swipe Reader Figure A-3. USB HID IntelliHead, 3-Track, 125mm Wire, 4.05mm Beam Arm, 5-Pin Molex 30
Appendix A. Drawings Figure A-4. USB HID IntelliHead, 3-Track, 6’ Cable, USB-A Connector, 100mm Black 31
iv te horized by MagTek to resell the products, in which event, this warranty ll, at its laced e, ek reserves the right to examine the . t, a three
USB HID IntelliHead Swipe Reader Figure A-5. USB HID IntelliHead, 3-Track, 6” Cable, USB-A Connector, 100mm Black 32
Appendix A. Drawings Figure A-6. USB HID IntelliHead, 3-Track, 125mm Wire, 5-pin Molex connector, 43mm rail 33
USB HID IntelliHead Swipe Reader Figure A-7. USB HID IntelliHead, 3-Track, 125mm Wire, 5-pin Connector, 90mm rail 34
Appendix A. Drawings Figure A-8. USB HID IntelliHead, 3-Track, 125mm Wire, 5-pin Molex Connector, 60mm Slim Profile 35
USB HID IntelliHead Swipe Reader 36 Figure A-9. USB HID IntelliHead, 3-Track, 125mm Wire, 5-pin Molex Connector, 90mm Slim Profile
vFCC WARNING STATEMENT n the ul mmunications. However, there is no guarantee that interference will not occur in a articular installation. FCC CO
TABLE OF CONTENTS SECTION 1. FEATURES AND SPECIFICATIONS...112225
TABLES AND FIGURES Figure 1-1. USB IntelliHead 3-Track...
viii Figure 1-1. USB IntelliHead 3-Track
SECTION 1. FEATURES AND SPECIFICATIONS The USB (Universal Serial Bus) HID (Human Interface Device) IntelliHead Swipe Reader is a compact magnetic s
Comments to this Manuals