Compaq 380578-B21 User Manual download pdf

See other side

IBRE

HANNEL

WITCH

8-/16-P

ORT

NIVERSAL

OUNTING

Installation Card

About This Card

This card identifies the contents of the universal mounting kit and provides

procedures for mounting a Fibre Channel (FC) 8-Port Switch

(380591–B21) or a FC 16-Port Switch (380578–B21/DS–DSGGA–AB)

into the following Compaq racks:

■ RETMA 41U or 42U

■ Compaq Classic

■ Metric SW600

Kit Contents

NOTE:

This kit contains parts for various rack installations. Not all kit

parts are needed for all rack installations.

1 Mounting brackets (2)

2 Extender brackets (2)

3 Slide brackets (2)

4 Bag of miscellaneous hardware:

■ Snap-on cable ties (2)

■ Clip nuts (4)

■ Alignment washers (8)

■ Pan head SEMS screws, 10-32 x 9/32 in (4)

■ Pan head SEMS screws, 10-32 x 5/8 in (16)

Tools Required

■ No. 2 Phillips screwdriver

Installation Process Orientation

Current or planned configuration of rack components determines which

installation process orientation to follow. Key consideration is how cables

are routed—at the rack front or rear. General rack configuration guidelines

include:

■ For RETMA 41U and metric SW600 racks, follow procedures as

oriented from the rack-front.

■ For RETMA 42U and Compaq Classic racks, either

orientation—rack-front or rack-rear—configuration is possible.

Install as desired.

Beginning the Installation Process

Determine the 2U installation location within the rack using the

rack-mounting template shipped with the 8- or 16-port switch.

IMPORTANT:

Ensure that the template-front and back are used according to the desired

installation orientation. In

rack-front

installations, the template-front is used at the

rack-front and template-back is used at the rack-rear. In

rack-rear

installations, the

template-front is used at the rack-rear and template-back is used at the rack-front.

1. Position the template-front on the vertical rails to match the template

hole pattern to the rail holes.

2. Pencil mark the front mounting bracket holes with an M.

3. Position the template-back on the rack-rear vertical rails, aligning the

template parallel with the rack-front pencil markings.

4. Pencil mark the rear mounting bracket holes with an M.

Attaching the Mounting Brackets

Attach two mounting brackets.

WARNING:

To reduce the risk of personal injury or equipment damage during

installation, never extend multiple components installed in the rack at the same

time. A rack might become unstable if more than one component is extended for

any reason.

For RETMA 41U racks:

1. Position each mounting bracket 1 with the rail holes pencil

marked M.

IMPORTANT:

Finger-tighten all three mounting bracket screws to facilitate alignment.

Then secure screws in the top and bottom mounting bracket holes prior to securing the

single screw at the rear of the bracket. Ensure the mounting bracket is parallel in the rack

from front to back.

2. Install a clip nut 2 and secure using pan head SEMS screws

(10-32 x 5/8 in).

For RETMA 42U and Compaq Classic racks:

1. Connect an extender bracket to each mounting bracket by finger

tightening two pan head SEMS screws (10-32 x 5/8 in).

2. Install an alignment washer into all rail holes (8) pencil marked M.

3. Position each mounting bracket to align with the alignment washers

and secure using pan head SEMS screws (10-32 x 5/8 in).

4. Fully tighten the four screws installed in step 1 using figure 3.

IMPORTANT:

To establish full strength of the extended bracket, ensure that screws

bonding the mounting bracket and extender bracket are fully tightened prior to proceeding.

CXO6803A

CXO6804A

CXO6783A

CXO6784A

CXO6785A

European Union Notice

Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the

Low Voltage Directive (73/23 EEC) issued by the Commission of the European Community.

Compliance with these directives implies conformity to the following European Norms (in

brackets are the equivalent international standards):

■

EN 55022 (CISPR 22)

Electromagnetic Interference

■

EN 50082-1 (IEC 801-2, IEC 801-3, IEC 801-4) 22)

Electromagnetic Immunity

■

EN 60950 (IEC 950)

Product Safety

NOTICE

The information in this document is subject to change without notice. COMPAQ COMPUTER

CORPORATION SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR

OMISSIONS CONTAINED HEREIN, NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES

RESULTING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL. THIS

INFORMATION IS PROVIDED “AS IS” AND COMPAQ COMPUTER CORPORATION DISCLAIMS

ANY WARRANTIES, EXPRESS, IMPLIED, OR STATUTORY AND EXPRESSLY DISCLAIMS THE

IMPLIED WARRANTIES OF MECHANTABILITY, FITNESS FOR PARTICULAR PURPOSE, GOOD

TITLE AND AGAINST INFRINGEMENT.

This publication contains information protected by copyright. No part of this

publication may be photocopied or reproduced in any form without prior written

consent from Compaq Computer Corporation.

Compaq and the COMPAQ STORAGEWORKS logo registered U.S. Patent and

Trademark Office.

FIBRE CHANNEL SWITCH, 8-/16-PORT UNIVERSAL MOUNTING KIT

First Edition (February 1999)

Part Number 120294-001

EK–GGAAB–IC. A01

Compaq Computer Corporation

Open Card Completely Before

Beginning Installation Procedures

1 2

Summary of Contents

Page 1 - Open Card Completely Before

See other sideFIBRE CHANNEL SWITCH, 8-/16-PORT UNIVERSAL MOUNTING KITInstallation CardAbout This CardThis card identifies the contents of the universa

Page 2 - Routing Power and Data Cables

For metric racks: 1. Position each mounting bracket 1 with the rail holes pencil marked M.2. Identify clip nut 2 mounting holes and install two clip n

Comments to this Manuals

No comments

Compaq 380578-B21 User Manual

Browse online or download User Manual for Network switches Compaq 380578-B21. Fibre Channel Switch, 8-/16-Port Universal Mounting Kit

Summary of Contents

Comments to this Manuals

Related products and manuals for Network switches Compaq 380578-B21