Compaq P1220 Service Manual download pdf (Page 160)

-1-6 -

Apple Macintosh

Computer

Macintosh Adapter

AD-A205 (Option)

AD-A205

MITSUBISHI

12 3

DB9-15P

D-SUB15P

Cable

SC-B110

SIGNAL-B SIGNAL-A

3.2.2 Connecting to An Apple Macintosh Computer

Figure 6 shows the SC-B110 cable and AD-A205

Adapter(option) to the video port in an Apple Macintosh.

For Macintosh Adapter AD-A205, contact your dealer.

1. Power off, both the monitor and the computer.

2. Set the DIP switches of Macintosh Adapter according

to the setting chart.

(See Section 7.3 Optional Macintosh Adapter AD-

A205 Settings)

3. Connect the 15-pin (DB-15P) end of the AD-A205

Adapter to the straight 15-pin connector on the

Macintosh video port on the computer or on the video

board.

4. Connect the sub-miniature 15-pin (DB9-15P) end of

the AD-A205 Adapter to the SC-B110 cable.

5. Connect the other end of the SC-B110 cable to the

DB9-15P receptacle on the back of the monitor.

6. Power on the monitor, then the Macintosh.

7. After using the system, power off the monitor, then the

Macintosh.

On the back of the monitor three kinds of plug-in connec-

tions are provided: AC power connector for the AC input,

two DB9-15P connectors for video signal input, and USB

ports for USB communication.

3.1 AC Power Connection

One end of the AC power cord is connected to the AC

power connector on the back of the monitor. The other end

is plugged into a properly grounded three-prong AC outlet.

The monitor’s auto-sensing power supply can automati-

cally detect 100-120V AC or 220-240V AC and 50 or 60Hz.

3.2 Signal Cable Connection

The DB9-15P(VGA) connector is provided for compatible

analog RGB outputs from your computer. Apple Macintosh

computers can also be interfaced with using the optional

Mitsubishi Macintosh adapter AD-A205.

3.2.1 Connecting to Any IBM VGA Compatible Sys-

tem

Figure 5 shows the SC-B110 cable connection to the Video

Graphics Array (VGA) port in an IBM Personal System/2

series, or any VGA compatible system.

1. Power off, both the monitor and the computer.

2. Connect the one end of the SC-B110 cable to the

DB9-15P connector on the VGA controller card.

3. Connect the other end of the SC-B110 cable to the

DB9-15P receptacle on the back of the monitor.

4. Power on the monitor, then the computer.

5. After using the system, power off the monitor, then

the computer.

CAUTION

The socket-outlet shall be installed near the equipment

and shall be easily accessible. During servicing, discon-

nect the plug from the socket-outlet.

INSTALLATION AND

CONNECTION

• For the Apple Macintosh Computers having a VGA

compatible port, steps 2 through 4 are not necessary.

Connect the end of the signal cable to the port directly.

• In case of Apple Macintosh G3 series, use "Control

Panel" of "Apple Menu" when selecting a resolution.

If select the resolution from "Control Bar", no screen may

be displayed and the computer may freeze.

Figure 5

Figure 6

NOTE

VGA

Compatible

System

Cable

SC-B110



Connect to Analog RGB

Connector (D-Sub 15p)

SIGNAL-B SIGNAL-A

1 2 ... 155 156 157 158 159 160 161 162 163 164 165 ... 209 210

Comments to this Manuals

No comments

Compaq P1220 Service Manual Page 160

Comments to this Manuals

Related products and manuals for TVs & monitors Compaq P1220