Compaq ProLiant DL980 - G7 Server User's Guide Page 68
- Page / 128
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Hardware options installation 68
• When returning a system board for service replacement, do not remove the TPM from the system
board. When requested, HP Service provides a TPM with the spare system board.
• Any attempt to remove an installed TPM from the system board breaks or disfigures the TPM security
rivet. Upon locating a broken or disfigured rivet on an installed TPM, administrators should consider
the system compromised and take appropriate measures to ensure the integrity of the system data.
• When using BitLocker™, always retain the recovery key/password. The recovery key/password is
required to enter Recovery Mode after BitLocker™ detects a possible compromise of system integrity.
• HP is not liable for blocked data access caused by improper TPM use. For operating instructions, see
the encryption technology feature documentation provided by the operating system.
Retaining the recovery key/password
The recovery key/password is generated during BitLocker™ setup, and can be saved and printed after
BitLocker™ is enabled. When using BitLocker™, always retain the recovery key/password. The recovery
key/password is required to enter Recovery Mode after BitLocker™ detects a possible compromise of
system integrity.
To help ensure maximum security, observe the following guidelines when retaining the recovery
key/password:
• Always store the recovery key/password in multiple locations.
• Always store copies of the recovery key/password away from the server.
• Do not save the recovery key/password on the encrypted hard drive.
Installing the Trusted Platform Module board
WARNING: To reduce the risk of personal injury, electric shock, or damage to the
equipment, remove the power cord to remove power from the server. The front panel Power
On/Standby button does not completely shut off system power. Portions of the power supply
and some internal circuitry remain active until AC power is removed.
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the
internal system components to cool before touching them.
1. Power down the server (on page 26).
2. Remove the access panel (on page 27).
3. Extend the server from the rack.
4. Remove the SPI board.
5. Locate the TPM connector.
CAUTION: Any attempt to remove an installed TPM from the system board breaks or
disfigures the TPM security rivet. Upon locating a broken or disfigured rivet on an installed
TPM, administrators should consider the system compromised and take appropriate measures
to ensure the integrity of the system data.
- HP ProLiant DL980 G7 Server 1
- User Guide 1
- Intended audience 2
- Contents 3
- Front panel components 7
- Front panel LEDs 8
- System Insight Display LEDs 9
- LED Component 10
- Hard drive LEDs 11
- Hard drive LED combinations 11
- Rear panel components 12
- Item Description 13
- Rear panel LEDs 14
- Power supply LED 15
- Fan location 16
- System board components 18
- System maintenance switch 19
- Expansion board components 20
- DIMM slot locations 22
- Device numbers 22
- SAS hard drive LEDs 23
- Battery pack LEDs 24
- Operations 26
- Remove the access panel 27
- Operations 29 29
- Rack planning resources 30
- Optimum environment 31
- Power requirements 32
- Rack warnings 33
- Installing hardware options 33
- Registering the server 34
- Introduction 35
- Processor options 35
- Install the heatsink 39
- Memory options 40
- DIMM identification 41
- DIMM installation guidelines 42
- Hemisphere mode 44
- Memory RAS 45
- Installing memory 47
- Hot-plug hard drive option 49
- 3. Install the hard drive 50
- Expansion board options 52
- Low profile I/O expander 59
- Cabling 71
- DVD-ROM drive cabling 72
- Configuration tools 73
- HP ROM-Based Setup Utility 73
- Using RBSU 74
- Auto-configuration process 74
- Boot options 75
- BIOS Serial Console 75
- Configuring lockstep memory 75
- Array Configuration Utility 76
- Management tools 78
- Erase Utility 79
- HP Systems Insight Manager 80
- Management Agents 80
- Redundant ROM support 80
- Diagnostic tools 81
- Integrated Management Log 82
- Array Diagnostic Utility 82
- Keeping the system current 83
- Care Pack 84
- Battery replacement 85
- Troubleshooting 86
- Symbols on equipment 87
- Warnings and cautions 87
- Symptom information 88
- Loose connections 89
- Service notifications 90
- Troubleshooting flowcharts 90
- General diagnosis flowchart 91
- Symptoms: 93
- Troubleshooting 95 95
- POST problems flowchart 96
- OS boot problems flowchart 97
- • Redundancy failure 100
- Troubleshooting 101 101
- FCC rating label 102
- Class A equipment 102
- Class B equipment 102
- Modifications 103
- • EMC Directive 2004/108/EC 104
- Japanese notice 106
- BSMI notice 106
- Korean notice 106
- Chinese notice 107
- Laser compliance 107
- Battery replacement notice 107
- (Geräuschemission) 108
- Wireless devices 108
- Brazilian notices 109
- Canadian notices 109
- Japanese notices 109
- Taiwan notices 109
- Electrostatic discharge 110
- Specifications 111
- Server Specifications 112
- Technical support 114
- Technical support 115 115
- Customer Self Repair 116
- Technical support 117 117
- Reparo feito pelo cliente 118
- Technical support 119 119
- Technical support 120 120
- Technical support 121 121
- Acronyms and abbreviations 122
- Index 125 125
- Index 126 126
- Index 127 127
- Index 128 128
Related products and manuals for Servers Compaq ProLiant DL980 - G7 Server
Servers Compaq ProLiant DL388p Specifications
(106 pages)
(106 pages)
© 2020, manymanuals.com. All rights reserved. | 2.190 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals